[cisco-ttl] Disconnect Problemi

From: yasinozgul <yasinozgul_at_....>
Date: Wed Aug 03 2005 - 17:10:46 EEST


Cisco 2651XM router üzerinde iki adet FXO karta 8 tane telefon hattı bağlı durumda. Disconnect problemi olduğu için disconnector'leri deiştirildi ancak sorun devam etti ve FXO kart değiştirildi. Sorun yine devam etti bunun üzerine IOS upgrade yapıldı ve şu anda üzerinde C2600 Software (C2600-ADVIPSERVICESK9-M), Version 12.3(11)T5 IOS bulunuyor. Sorun halen devam ediyor, sık sorun çıkaran iki portla ilgili çıktıları aşağıya ekledim. Konu ile ilgili yardımlarınızı bekliyorum.

Teşekkürler, saygılar...

sh voice port 1/0/1

Foreign Exchange Office 1/0/1 Slot is 1, Sub-unit is 0, Port is 1  Type of VoicePort is FXO
 Operation State is UP
 Administrative State is UP
 The Last Interface Down Failure Cause is Administrative Shutdown  Noise Regeneration is enabled
 Non Linear Processing is enabled
 Non Linear Mute is disabled
 Non Linear Threshold is -21 dB
 Music On Hold Threshold is Set to -38 dBm  In Gain is Set to 0 dB
 Out Attenuation is Set to 3 dB
 Echo Cancellation is enabled
 Echo Cancellation NLP mute is disabled
 Echo Cancellation NLP threshold is -21 dB  Echo Cancel Coverage is set to 64 ms
 Echo Cancel worst case ERL is set to 6 dB

 Playout-delay Mode is set to adaptive
 Playout-delay Nominal is set to 60 ms
 Playout-delay Maximum is set to 250 ms
 Playout-delay Minimum mode is set to default, value 40 ms 
 Playout-delay Fax is set to 300 ms

 Connection Mode is plar
 Connection Number is 22158
 Initial Time Out is set to 10 s
 Interdigit Time Out is set to 3 s
 Call Disconnect Time Out is set to 60 s  Ringing Time Out is set to 180 s
 Wait Release Time Out is set to 30 s
 Companding Type is u-law
 Region Tone is set for TR

 Analog Info Follows:
 Currently processing Voice
 Maintenance Mode Set to None (not in mtc mode)  Number of signaling protocol errors are 0  Impedance is set to 600r Ohm
 Station name None, Station number None
 Translation profile (Incoming):
 Translation profile (Outgoing):

 Voice card specific Info Follows:
 Signal Type is loopStart
 Battery-Reversal is enabled
 Number Of Rings is set to 1
 Supervisory Disconnect is signal
 Answer Supervision is inactive
 Hook Status is Off Hook
 Ring Detect Status is inactive
 Ring Ground Status is inactive
 Tip Ground Status is inactive
 Dial Out Type is dtmf
 Digit Duration Timing is set to 100 ms
 InterDigit Duration Timing is set to 100 ms  Pulse Rate Timing is set to 10 pulses/second  InterDigit Pulse Duration Timing is set to 750 ms  Percent Break of Pulse is 65 percent
 GuardOut timer is 2000 ms
 Minimum ring duration timer is 125 ms
 Hookflash-in Timing is set to 600 ms
 Hookflash-out Timing is set to 400 ms


sh voice port 1/1/3

Foreign Exchange Office 1/1/3 Slot is 1, Sub-unit is 1, Port is 3  Type of VoicePort is FXO
 Operation State is DORMANT
 Administrative State is UP
 The Last Interface Down Failure Cause is Administrative Shutdown  Noise Regeneration is enabled
 Non Linear Processing is enabled
 Non Linear Mute is disabled
 Non Linear Threshold is -21 dB
 Music On Hold Threshold is Set to -38 dBm  In Gain is Set to 0 dB
 Out Attenuation is Set to 3 dB
 Echo Cancellation is enabled
 Echo Cancellation NLP mute is disabled
 Echo Cancellation NLP threshold is -21 dB  Echo Cancel Coverage is set to 64 ms
 Echo Cancel worst case ERL is set to 6 dB

 Playout-delay Mode is set to adaptive
 Playout-delay Nominal is set to 60 ms
 Playout-delay Maximum is set to 250 ms
 Playout-delay Minimum mode is set to default, value 40 ms 
 Playout-delay Fax is set to 300 ms

 Connection Mode is plar
 Connection Number is 22158
 Initial Time Out is set to 10 s
 Interdigit Time Out is set to 10 s
 Call Disconnect Time Out is set to 60 s  Ringing Time Out is set to 180 s
 Wait Release Time Out is set to 30 s
 Companding Type is u-law
 Region Tone is set for TR

 Analog Info Follows:
 Currently processing none
 Maintenance Mode Set to None (not in mtc mode)  Number of signaling protocol errors are 0  Impedance is set to 600r Ohm
 Station name None, Station number None
 Translation profile (Incoming):
 Translation profile (Outgoing):

 Voice card specific Info Follows:
 Signal Type is loopStart
 Battery-Reversal is enabled
 Number Of Rings is set to 1
 Supervisory Disconnect is signal
 Answer Supervision is inactive
 Hook Status is On Hook
 Ring Detect Status is inactive
 Ring Ground Status is inactive
 Tip Ground Status is inactive
 Dial Out Type is dtmf
 Digit Duration Timing is set to 100 ms
 InterDigit Duration Timing is set to 100 ms  Pulse Rate Timing is set to 10 pulses/second  InterDigit Pulse Duration Timing is set to 750 ms  Percent Break of Pulse is 65 percent
 GuardOut timer is 2000 ms
 Minimum ring duration timer is 125 ms
 Hookflash-in Timing is set to 600 ms
 Hookflash-out Timing is set to 400 ms

--
Cisco Teknik Tartisma Listesi (Cisco-ttl)

Bu listede onerilen degisikliklerin uygulanmasindaki tum sorumluluk 
kullaniciya aittir. Liste yoneticileri, oneride bulunan liste uyeleri ya da 
bu uyelerin calistigi kuruluslar herhangi bir sekilde sorumlu tutulamazlar. 
Yahoo! Groups Links


<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/cisco-ttl/
<*> To unsubscribe from this group, send an email to:
cisco-ttl-unsubscribe@yahoogroups.com
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
Received on Wed Aug 3 17:17:00 2005

This archive was generated by hypermail 2.1.8 : Wed Aug 03 2005 - 17:17:02 EEST