Re: [cisco-ttl] uluslararasi ISDN arama

From: Devrim Yener KUCUK (dkucuk_at_cisco.com)
Date: Tue Mar 29 2005 - 12:56:15 EEST


Merhaba Hakan,

SET-UP dan sonra CONNECT gormuyorum ve RX tarafinda disconnect oluyor.

.Mar 25 13:06:11.397: ISDN BR3/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x9C
.Mar 25 13:06:21.911: ISDN BR3/0 Q931: RX <- DISCONNECT pd = 8 callref = 0x9C
        Cause i = 0x8092 - No user responding

ISDN switch'in bekledigi zorunlu bir parametre mi var?
Neden disconnect ettiklerini sorar misin telco tarafina?

Bu ciktilardan sorun ISDN switch tarafinda gorunuyor

Devrim

  ----- Original Message -----
  From: Hakan AGIRKAYA
  To: cisco-ttl_at_yahoogroups.com
  Sent: Friday, March 25, 2005 3:15 PM
  Subject: Re: [cisco-ttl] uluslararasi ISDN arama

  Devrim,
  istedigin ciktilari asagida bulabilirsin.
  Tesekkurler,
  Hakan

  ISDNRouter#sh ver
  Cisco Internetwork Operating System Software
  IOS (tm) 3600 Software (C3660-JS-M), Version 12.3(1), RELEA
  Copyright (c) 1986-2003 by cisco Systems, Inc.
  Compiled Thu 15-May-03 06:06 by dchih
  Image text-base: 0x60008954, data-base: 0x61F20000

  ROM: System Bootstrap, Version 12.0(6r)T, RELEASE SOFTWARE

  ISDNRouter uptime is 28 weeks, 2 days, 1 hour, 21 minutes
  System returned to ROM by reload
  System restarted at 14:34:13 Turkey Wed Sep 8 2004
  System image file is "flash:c3660-js-mz.123-1.bin"

  cisco 3660 (R527x) processor (revision 1.0) with 90112K/819
  Processor board ID
  R527x CPU at 225Mhz, Implementation 40, Rev 10.0, 2048KB L2
  Bridging software.
  X.25 software, Version 3.0.0.
  SuperLAT software (copyright 1990 by Meridian Technology Co
  TN3270 Emulation software.
  Basic Rate ISDN software, Version 1.1.

  3660 Chassis type: ENTERPRISE
  2 FastEthernet/IEEE 802.3 interface(s)
  2 Serial(sync/async) network interface(s)
  4 ISDN Basic Rate interface(s)
  DRAM configuration is 64 bits wide with parity disabled.
  125K bytes of non-volatile configuration memory.
  32768K bytes of processor board System flash (Read/Write)

  Configuration register is 0x2102

  ISDNRouter#isdn test call interface brI 3/0 00302102880197
  ISDNRouter#
  .Mar 25 13:06:06.189: BR3/0 DDR: Attempting to dial 00302102880197
  28w2d: %ISDN-6-LAYER2UP: Layer 2 for Interface BR3/0, TEI 66 changed to up
  .Mar 25 13:06:06.209: ISDN BR3/0 Q931: TX -> SETUP pd = 8 callref = 0x1C
          Bearer Capability i = 0x8890
                  Standard = CCITT
                  Transer Capability = Unrestricted Digital
                  Transfer Mode = Circuit
                  Transfer Rate = 64 kbit/s
          Channel ID i = 0x83
          Called Party Number i = 0x80, '00302102880197'
                  Plan:Unknown, Type:Unknown
  .Mar 25 13:06:07.209: ISDN BR3/0 Q931: TX -> SETUP pd = 8 callref = 0x1C
          Bearer Capability i = 0x8890
                  Standard = CCITT
                  Transer Capability = Unrestricted Digital
                  Transfer Mode = Circuit
                  Transfer Rate = 64 kbit/s
          Channel ID i = 0x83
          Called Party Number i = 0x80, '00302102880197'
                  Plan:Unknown, Type:Unknown
  .Mar 25 13:06:07.349: ISDN BR3/0 Q931: RX <- SETUP_ACK pd = 8 callref = 0x9C
          Channel ID i = 0x89
  .Mar 25 13:06:11.397: ISDN BR3/0 Q931: RX <- CALL_PROC pd = 8 callref = 0x9C
  .Mar 25 13:06:21.911: ISDN BR3/0 Q931: RX <- DISCONNECT pd = 8 callref = 0x9C
          Cause i = 0x8092 - No user responding
  .Mar 25 13:06:21.915: BRI3/0: wait for isdn carrier timeout, call id=0x8021
  .Mar 25 13:06:21.915: ISDN BR3/0 Q931: TX -> RELEASE pd = 8 callref = 0x1C
          Cause i = 0x8092 - No user responding
  .Mar 25 13:06:22.012: ISDN BR3/0 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x9C
  28w2d: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR3/0, TEI 66 changed to down
  ISDNRouter#
    ----- Original Message -----
    From: Devrim Yener KUCUK
    To: cisco-ttl_at_yahoogroups.com
    Sent: Friday, March 25, 2005 2:33 PM
    Subject: Re: [cisco-ttl] uluslararasi ISDN arama

    Hakan

    Ayni iki debug "debug isdn q931" "debug dialer" ciktisini "service time
    debug date msec" komutunu enable edip gonder misin?
    Ek olarak bu routerin " sh ver" ciktisi lutfen.

    ISDN Q931 spec de asagidaki 3 mesaj zorunludur ( digerler optional)
    SET-UP
    CONNECT
    ve
    CONNECT_ACK

    SET_UP dan sonra CONNECT gelmiyor, ISDN switch sorununa benziyor ama
    surelere bir bakalim

    Tesekkur

    Devrim

    ----- Original Message -----
    From: "Hakan AĞIRKAYA" <hakan_at_agirkaya.com>
    To: <cisco-ttl_at_yahoogroups.com>
    Sent: Friday, March 25, 2005 1:26 PM
    Subject: [cisco-ttl] uluslararasi ISDN arama

>
> Devrim merhaba,
>
> Asagida daha ayrintili debug ciktilarini bulabilirsin. Asil baglanti
    kurmam gereken router ( 3660 ) uzerinden aldim bunlari.
> Cause i = 0x8092 - No user responding hakkında bilgiye ulaşamiyorum.
>
>
> ISDNRouter#isdn test call interface brI 3/0 02123650376
> 28w2d: BR3/0 DDR: Attempting to dial 02123650376
> 28w2d: ISDN BR3/0 EVENT: UserIdle: callid 0x801A received ISDN_CALL (0x0)
> 28w2d: ISDN BR3/0 Q921: User TX -> SABMEp sapi=0 tei=66
> 28w2d: ISDN BR3/0 Q921: User RX <- UAf sapi=0 tei=66
> 28w2d: %ISDN-6-LAYER2UP: Layer 2 for Interface BR3/0, TEI 66 changed to up
> 28w2d: ISDN BR3/0 Q921: User TX -> INFO sapi=0 tei=66, ns=0 nr=0
> 28w2d: ISDN BR3/0 Q931: SETUP pd = 8 callref = 0x15
> Bearer Capability i = 0x8890
> Standard = CCITT
> Transer Capability = Unrestricted Digital
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0x83
> Called Party Number i = 0x80, '02123650376'
> Plan:Unknown, Type:Unknown
> 28w2d: ISDN BR3/0 Q921: User RX <- RR sapi=0 tei=66 nr=1
> 28w2d: ISDN BR3/0 Q921: User RX <- INFO sapi=0 tei=66, ns=0 nr=1
> 28w2d: ISDN BR3/0 Q931: CALL_PROC pd = 8 callref = 0x95
> Channel ID i = 0x89
> 28w2d: ISDN BR3/0 Q921: User TX -> RR sapi=0 tei=66 nr=1
> 28w2d: ISDN BR3/0 EVENT: process_rxstate: ces/callid 1/0x801A calltype 1
    HOST_PR
> OCEEDING
> 28w2d: ISDN BR3/0 Q921: User RX <- INFO sapi=0 tei=66, ns=1 nr=1
> 28w2d: ISDN BR3/0 Q931: ALERTING pd = 8 callref = 0x95
> 28w2d: ISDN BR3/0 Q921: User TX -> RR sapi=0 tei=66 nr=2
> 28w2d: ISDN BR3/0 EVENT: process_rxstate: ces/callid 1/0x801A calltype 1
    HOST_AL
> ERTING
> 28w2d: ISDN BR3/0 Q921: User RX <- INFO sapi=0 tei=66, ns=2 nr=1
> 28w2d: ISDN BR3/0 Q931: CONNECT pd = 8 callref = 0x95
> Date/Time i = 0x0503190E0F
> 28w2d: ISDN BR3/0 Q921: User TX -> RR sapi=0 tei=66 nr=3
> 28w2d: ISDN BR3/0 EVENT: process_rxstate: ces/callid 1/0x801A calltype 1
    HOST_CO
> NNECT
> 28w2d: %LINK-3-UPDOWN: Interface BRI3/0:1, changed state to up
> 28w2d: ISDN BR3/0 Q921: User TX -> INFO sapi=0 tei=66, ns=1 nr=3
> 28w2d: ISDN BR3/0 Q931: CONNECT_ACK pd = 8 callref = 0x15
> 28w2d: ISDN BR3/0 Q921: User RX <- RR sapi=0 tei=66 nr=2
> 28w2d: %ISDN-6-CONNECT: Interface BRI3/0:1 is now connected to 02123650376
> 28w2d: ISDN BR3/0 Q921: User RX <- INFO sapi=0 tei=66, ns=3 nr=2
> 28w2d: ISDN BR3/0 Q931: DISCONNECT pd = 8 callref = 0x95
> Cause i = 0x8290 - Normal call clearing
> 28w2d: ISDN BR3/0 Q921: User TX -> RR sapi=0 tei=66 nr=4
> 28w2d: ISDN BR3/0 EVENT: process_rxstate: ces/callid 1/0x801A calltype 1
    HOST_DI
> SCONNECT
> 28w2d: %ISDN-6-DISCONNECT: Interface BRI3/0:1 disconnected from
    02123650376 , c
> all lasted 6 seconds
> 28w2d: %LINK-3-UPDOWN: Interface BRI3/0:1, changed state to down
> 28w2d: ISDN BR3/0 Q921: User TX -> INFO sapi=0 tei=66, ns=2 nr=4
> 28w2d: ISDN BR3/0 Q931: RELEASE pd = 8 callref = 0x15
> Cause i = 0x8090 - Normal call clearing
> 28w2d: BR3/0:1 DDR: disconnecting call
> 28w2d: ISDN BR3/0 Q921: User RX <- RR sapi=0 tei=66 nr=3
> 28w2d: ISDN BR3/0 Q921: User RX <- INFO sapi=0 tei=66, ns=4 nr=3
> 28w2d: ISDN BR3/0 Q931: RELEASE_COMP pd = 8 callref = 0x95
> 28w2d: ISDN BR3/0 Q921: User TX -> RR sapi=0 tei=66 nr=5
> 28w2d: ISDN BR3/0 EVENT: process_rxstate: ces/callid 1/0x801A calltype 1
    HOST_DI
> SCONNECT_ACK
> 28w2d: ISDN BR3/0 Q921: User TX -> RRp sapi=0 tei=66 nr=5
> 28w2d: ISDN BR3/0 Q921: User RX <- RRf sapi=0 tei=66 nr=3isdn test call
    interfac
> ISDNRouter#isdn test call interface brI 3/0 02123650376
> 28w2d: ISDN BR3/0 Q921: User RX <- DISCp sapi=0 tei=66
> 28w2d: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR3/0, TEI 66 changed to
    down
> 28w2d: I
>
>
>
> ISDNRouter#isdn test call interface brI 3/0 00302102880197
> 28w2d: BR3/0 DDR: Attempting to dial 00302102880197
> 28w2d: ISDN BR3/0 EVENT: UserIdle: callid 0x801B received ISDN_CALL (0x0)
> 28w2d: ISDN BR3/0 Q921: User TX -> SABMEp sapi=0 tei=66
> 28w2d: ISDN BR3/0 Q921: User RX <- UAf sapi=0 tei=66
> 28w2d: %ISDN-6-LAYER2UP: Layer 2 for Interface BR3/0, TEI 66 changed to up
> 28w2d: ISDN BR3/0 Q921: User TX -> INFO sapi=0 tei=66, ns=0 nr=0
> 28w2d: ISDN BR3/0 Q931: SETUP pd = 8 callref = 0x16
> Bearer Capability i = 0x8890
> Standard = CCITT
> Transer Capability = Unrestricted Digital
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0x83
> Called Party Number i = 0x80, '00302102880197'
> Plan:Unknown, Type:Unknown
> 28w2d: ISDN BR3/0 Q921: S7_T200_EXPIRY: VA = 0, VS = 1
> 28w2d: ISDN BR3/0 Q921: User TX -> INFOp sapi=0 tei=66, ns=0 nr=0
> 28w2d: ISDN BR3/0 Q931: SETUP pd = 8 callref = 0x16
> Bearer Capability i = 0x8890
> Standard = CCITT
> Transer Capability = Unrestricted Digital
> Transfer Mode = Circuit
> Transfer Rate = 64 kbit/s
> Channel ID i = 0x83
> Called Party Number i = 0x80, '00302102880197'
> Plan:Unknown, Type:Unknown
> 28w2d: ISDN BR3/0 Q921: User RX <- RRf sapi=0 tei=66 nr=1
> 28w2d: ISDN BR3/0 Q921: User RX <- INFO sapi=0 tei=66, ns=0 nr=1
> 28w2d: ISDN BR3/0 Q931: SETUP_ACK pd = 8 callref = 0x96
> Channel ID i = 0x89
> 28w2d: ISDN BR3/0 Q921: User TX -> RR sapi=0 tei=66 nr=1
> 28w2d: ISDN BR3/0 EVENT: process_rxstate: ces/callid 1/0x801B calltype 1
    HOST_IN
> FORMATION
> 28w2d: ISDN BR3/0 Q921: User RX <- INFO sapi=0 tei=66, ns=1 nr=1
> 28w2d: ISDN BR3/0 Q931: CALL_PROC pd = 8 callref = 0x96
> 28w2d: ISDN BR3/0 Q921: User TX -> RR sapi=0 tei=66 nr=2
> 28w2d: ISDN BR3/0 EVENT: process_rxstate: ces/callid 1/0x801B calltype 1
    HOST_PR
> OCEEDING
> 28w2d: ISDN BR3/0 Q921: User TX -> RRp sapi=0 tei=66 nr=2
> 28w2d: ISDN BR3/0 Q921: User RX <- RRf sapi=0 tei=66 nr=1
> 28w2d: ISDN BR3/0 Q921: User RX <- INFO sapi=0 tei=66, ns=2 nr=1
> 28w2d: ISDN BR3/0 Q931: DISCONNECT pd = 8 callref = 0x96
> Cause i = 0x8092 - No user responding
> 28w2d: ISDN BR3/0 Q921: User TX -> RR sapi=0 tei=66 nr=3
> 28w2d: ISDN BR3/0 EVENT: process_rxstate: ces/callid 1/0x801B calltype 1
    HOST_DI
> SCONNECT
> 28w2d: BRI3/0: wait for isdn carrier timeout, call id=0x801B
> 28w2d: ISDN BR3/0 Q921: User TX -> INFO sapi=0 tei=66, ns=1 nr=3
> 28w2d: ISDN BR3/0 Q931: RELEASE pd = 8 callref = 0x16
> Cause i = 0x8092 - No user responding
> 28w2d: ISDN BR3/0 Q921: User RX <- RR sapi=0 tei=66 nr=2
> 28w2d: ISDN BR3/0 Q921: User RX <- INFO sapi=0 tei=66, ns=3 nr=2
> 28w2d: ISDN BR3/0 Q931: RELEASE_COMP pd = 8 callref = 0x96
> 28w2d: ISDN BR3/0 Q921: User TX -> RR sapi=0 tei=66 nr=4
> 28w2d: ISDN BR3/0 EVENT: process_rxstate: ces/callid 1/0x801B calltype 1
    HOST_DI
> SCONNECT_ACK
> 28w2d: ISDN BR3/0 Q921: User TX -> RRp sapi=0 tei=66 nr=4
> 28w2d: ISDN BR3/0 Q921: User RX <- RRf sapi=0 tei=66 nr=2
> 28w2d: ISDN BR3/0 Q921: User RX <- DISCp sapi=0 tei=66
> 28w2d: %ISDN-6-LAYER2DOWN: Layer 2 for Interface BR3/0, TEI 66 changed to
    down
> 28w2d: ISDN BR3/0 Q921: User TX -> UAf sapi=0 tei=66
> ISDNRouter#
> ISDNRouter#
> ISDNRouter#
> ISDNRouter#
> ISDNRouter#
>
> [Non-text portions of this message have been removed]
>
>
>
> --
>
> Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.
>
> Listede onerilen cozumlerin uygulanmasindaki tum sorumluluk kullaniciya
    aittir. Liste yoneticileri, liste uyeleri ya da bu uyelerin calistigi
    kuruluslar herhangi bir sekilde sorumlu tutulamazlar.
>
> Listeden cikmak için cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir
    e-posta gönderebilirsiniz.
> Yahoo! Groups Links
>
>
>
>
>

    --

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listede onerilen cozumlerin uygulanmasindaki tum sorumluluk kullaniciya aittir. Liste yoneticileri, liste uyeleri ya da bu uyelerin calistigi kuruluslar herhangi bir sekilde sorumlu tutulamazlar.

    Listeden cikmak için cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir e-posta gönderebilirsiniz.

          Yahoo! Groups Sponsor
                ADVERTISEMENT
               
         
         

  ------------------------------------------------------------------------------
    Yahoo! Groups Links

      a.. To visit your group on the web, go to:
      http://groups.yahoo.com/group/cisco-ttl/
        
      b.. To unsubscribe from this group, send an email to:
      cisco-ttl-unsubscribe_at_yahoogroups.com
        
      c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

  [Non-text portions of this message have been removed]

  --

  Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

  Listede onerilen cozumlerin uygulanmasindaki tum sorumluluk kullaniciya aittir. Liste yoneticileri, liste uyeleri ya da bu uyelerin calistigi kuruluslar herhangi bir sekilde sorumlu tutulamazlar.

  Listeden cikmak için cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir e-posta gönderebilirsiniz.

        Yahoo! Groups Sponsor
              ADVERTISEMENT
             
       
       

------------------------------------------------------------------------------
  Yahoo! Groups Links

    a.. To visit your group on the web, go to:
    http://groups.yahoo.com/group/cisco-ttl/
      
    b.. To unsubscribe from this group, send an email to:
    cisco-ttl-unsubscribe_at_yahoogroups.com
      
    c.. Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service.

[Non-text portions of this message have been removed]

--

Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

Listede onerilen cozumlerin uygulanmasindaki tum sorumluluk kullaniciya aittir. Liste yoneticileri, liste uyeleri ya da bu uyelerin calistigi kuruluslar herhangi bir sekilde sorumlu tutulamazlar.

Listeden cikmak için cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir e-posta gönderebilirsiniz. Yahoo! Groups Links

<*> To visit your group on the web, go to: http://groups.yahoo.com/group/cisco-ttl/

<*> To unsubscribe from this group, send an email to: cisco-ttl-unsubscribe_at_yahoogroups.com

<*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/



This archive was generated by hypermail 2.1.3 : Tue Mar 29 2005 - 12:56:29 EEST