RE: [cisco-ttl] flash yukleme sorunu

From: Burak Ergun \(bergun\) (bergun_at_cisco.com)
Date: Tue Feb 01 2005 - 09:00:31 GMT

  • Next message: ozkan karacayoglu: "RE: [cisco-ttl] ids sorunu.."

    IOS version ile ilgili olabilir
    Aşağıdaki stepler ile yapmayı deneyebilirsin.

    Step 1 Log into the router via the console port using Telnet or terminal emulation software. (If you use terminal emulation software, configure the software settings to 9600 baud, no parity, 8 data bits, and 1 stop bit.)
    Step 2 When the router boots up, enter the enable mode, as follows:
    router> enable

    password: <password>
    router#
     
    Step 3 Erase the contents of the Flash memory partition except the one currently in use (this partition will be in the Read ONLY state in the partition listing), as shown below.
    router# erase flash

    Partition Size Used Free Bank-Size State Copy Mode
              1 8192K 3724K 4467K 8192K Read ONLY RXBOOT-manual
              2 8192K 3724K 4467K 8192K Read/Write Direct
     
    System flash directory, partition 2:
    File Length Name/status
              1 3813972 cpa25-y-l.111-6.1
    [3814036 bytes used, 4574572 available, 8388608 total]
     
    Erase flash device, partition 2? [confirm]
    Are you sure? [yes/no]: y

    Erasing device... eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee ...erased
     
    router#

    Note If you have more than two Flash memory partitions, you must perform the previous step for each of the partitions to be erased.

    Step 4 Enter the show flash command to verify that the desired Flash memory partitions have been erased:
    router# show flash

    System flash directory, partition 1:
    File Length Name/status
              1 3813972 cpa25-y-l.111-6.1
    [3814036 bytes used, 4574572 available, 8388608 total]
    8192K bytes of processor board System flash (Read ONLY)
     
     
    System flash directory, partition 2:
    No files in System flash
    [0 bytes used, 8388608 available, 8388608 total]
    8192K bytes of processor board System flash (Read/Write)
     
    You are now ready to unpartition the Flash memory.
    Step 5 Enter the configuration mode and enter the partition command to create a single Flash memory partition, as follows:
    router# configure terminal

    Enter configuration commands, one per line. End with cntrl/z.
    router(config)# partition flash 1

     
    Step 6 Exit the configuration mode and verify that flash memory now has a single partition, as follows:
    router(config)# exit


     

    -----Original Message-----
    From: Emre BALCI [mailto:emrebalci_at_yahoo.com]
    Sent: 01 February 2005, Tuesday 12:11
    To: cisco-ttl_at_yahoogroups.com
    Subject: RE: [cisco-ttl] flash yukleme sorunu


    partition flash 1 16 yaziyorum
    requested partitioning cannot be done hatas&#305; al&#305;yorum

    --- "Burak Ergun (bergun)" <bergun_at_cisco.com> wrote:

    >
    > Global configuration prompt'da "partition flash: 1
    > 16 " komutunu kullanýp tek partition yapabilirsin
    >
    > -----Original Message-----
    > From: Emre BALCI [mailto:emrebalci_at_yahoo.com]
    > Sent: 01 February 2005, Tuesday 11:18
    > To: cisco-ttl_at_yahoogroups.com
    > Subject: [cisco-ttl] flash yukleme sorunu
    >
    >
    > Selamlar...
    > 2500 16 mb flash l&#305; bir router a bir ios yukleyecem yaklas&#305;k
    > 12 mb fakat flash 8 li 2 partitiondan olusuyor gorunuyor yuklerken
    > flash size exceded hatas&#305; al&#305;yorum ne yapabilirim ?
    >
    >
    >
    > __________________________________
    > Do you Yahoo!?
    > Meet the all-new My Yahoo! - Try it today!
    > http://my.yahoo.com
    >
    >
    >
    >
    > Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.
    >
    > Listeden cikmak için
    > cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir e-posta
    > gönderebilirsiniz.
    > Yahoo! Groups Links
    >
    >
    >
    >
    >
    >
    > Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.
    >
    > Listeden cikmak için
    > cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir e-posta
    > gönderebilirsiniz.
    > Yahoo! Groups Links
    >
    >
    > cisco-ttl-unsubscribe_at_yahoogroups.com
    >
    >
    >
    >
    >
    >


    __________________________________________________
    Do You Yahoo!?
    Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com


    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak için cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir e-posta gönderebilirsiniz.
    Yahoo! Groups Links



     

    [Non-text portions of this message have been removed]

    Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.

    Listeden cikmak iin cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir e-posta gnderebilirsiniz.
    Yahoo! Groups Links

    <*> To visit your group on the web, go to:
        http://groups.yahoo.com/group/cisco-ttl/

    <*> To unsubscribe from this group, send an email to:
        cisco-ttl-unsubscribe_at_yahoogroups.com

    <*> Your use of Yahoo! Groups is subject to:
        http://docs.yahoo.com/info/terms/
     



    This archive was generated by hypermail 2.1.5 : Tue Feb 01 2005 - 13:01:18 GMT