[cisco-ttl] Dial Backup iletişim problemi.

Merhaba  

denemesini yaptığım dial backup conf ile ilgili bağlantı problemi yaşıyorum.Conf ve gerekli debug ları gönderiyorum.yardımcı olabilirseniz sevinirim.  

Arayan router üzerinde fastethernet çıkardığım zaman async devreye giriyor karşıyı arıyor (lokalde dahili aratıyorum)bağlantı kuruluyor ama taraflar birbirlerine ulaşamıyor.

Nerede eksik yapıyorum.  

Conf  

Aranan router (2821 üzerinde NM-8A/S modül) Modem us robotics  

modemcap entry usr:MSC=& FS0=1 & C1&D2;&H1;&R2;&B1;&W;  

interface Loopback0

 ip address 1.1.1.1 255.255.255.255  

interface Serial1/0

 physical-layer async

 ip unnumbered Loopback0

 encapsulation ppp

 dialer in-band

 dialer-group 1

 async mode dedicated

 no peer default ip address

 no fair-queue  

ip route 2.2.2.2 255.255.255.255 Serial1/0  

line 66

 modem InOut

 modem autoconfigure type usr_courier

 transport input all

 speed 115200

 flowcontrol hardware  

Arayan Router (3660 üzerinde aux port) Modem us robotics  

chat-script CALLOUT "" "atdt\T" TIMEOUT 60 CONNECT \c

modemcap entry usr:MSC=& FS0=1 & C1&D2;&H1;&R2;&B1;&W;  

interface Loopback0

 ip address 2.2.2.2 255.255.255.255

!

interface FastEthernet0/0

 ip address 192.168.10.202 255.255.255.0

 backup interface Async225

 ip policy route-map dene

 duplex auto

 speed auto  

interface Async225

 ip unnumbered Loopback0

 encapsulation ppp

 dialer in-band

 dialer map ip 1.1.1.1 name sehenet modem-script CALLOUT 27

 dialer-group 1

 async mode dedicated

 no peer default ip address

 no fair-queue  

ip route 1.1.1.1 255.255.255.255 Async225  

dialer-list 1 protocol ip permit  

line aux 0

 script dialer CALLOUT

 modem InOut

 modem autoconfigure type usr_courier

 transport input all

 speed 115200

 flowcontrol hardware    

Arayan router ethernet çıkardığım zaman Aşağıdaki gibi  

*Mar 1 00:51:43.147: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to down

Router#

*Mar 1 00:51:44.151: %LINK-3-UPDOWN: Interface Async225, changed state to down

Router#

Router#ping 1.1.1.1

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:  

*Mar 1 00:52:43.091: As225 DDR: place call

*Mar 1 00:52:43.091: As225 DDR: Dialing cause ip (s=2.2.2.2, d=1.1.1.1)

*Mar 1 00:52:43.091: As225 DDR: Attempting to dial 27

*Mar 1 00:52:43.091: CHAT225: Attempting async line dialer script

*Mar 1 00:52:43.091: CHAT225: Dialing using Modem script: CALLOUT & System script: none

*Mar 1 00:52:43.095: CHAT225: process started

*Mar 1 00:52:43.095: CHAT225: Asserting DTR

*Mar 1 00:52:43.095: CHAT225: Chat script CALLOUT started

*Mar 1 00:52:43.095: CHAT225: Sending string: atdt\T<27>

*Mar 1 00:52:43.095: CHAT225: Expecting string: CONNECT.....

Success rate is 0 percent (0/5)

Router#

*Mar 1 00:52:56.327: CHAT225: Completed match for expect: CONNECT

*Mar 1 00:52:56.327: CHAT225: Sending string: \c

*Mar 1 00:52:56.327: CHAT225: Chat script CALLOUT finished, status = Success

*Mar 1 00:52:58.327: %LINK-3-UPDOWN: Interface Async225, changed state to up

*Mar 1 00:52:58.327: As225 DDR: Dialer statechange to up

*Mar 1 00:52:58.327: As225 DDR: Dialer call has been placed

*Mar 1 00:52:58.671: As225 DDR: dialer protocol up

*Mar 1 00:52:59.327: %LINEPROTO-5-UPDOWN: Line protocol on Interface Async225, changed state to up

Router#

Router#ping 1.1.1.1  

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds:

.....

Success rate is 0 percent (0/5)    

Aranan router da da  

*Sep 17 16:24:27.022: %LINK-3-UPDOWN: Interface Serial1/0, changed state to up

*Sep 17 16:24:27.022: Se1/0 DDR: Dialer statechange to up

*Sep 17 16:24:27.022: Se1/0 DDR: Dialer received incoming call from <unknown>

*Sep 17 16:24:27.022: Se1/0 PPP: Using dialer call direction

*Sep 17 16:24:27.022: Se1/0 PPP: Treating connection as a callin

*Sep 17 16:24:27.022: Se1/0 PPP: Session handle[3800001F] Session id[19]

*Sep 17 16:24:27.022: Se1/0 PPP: Phase is ESTABLISHING, Passive Open

*Sep 17 16:24:27.022: Se1/0 LCP: State is Listen

*Sep 17 16:24:27.138: Se1/0 LCP: I CONFREQ [Listen] id 81 len 20

*Sep 17 16:24:27.138: Se1/0 LCP: ACCM 0x000A0000 (0x0206000A0000)

*Sep 17 16:24:27.138: Se1/0 LCP: MagicNumber 0x01C6CCA9 (0x050601C6CCA9)

*Sep 17 16:24:27.138: Se1/0 LCP: PFC (0x0702)

*Sep 17 16:24:27.138: Se1/0 LCP: ACFC (0x0802)

*Sep 17 16:24:27.138: Se1/0 PPP: Authorization required

*Sep 17 16:24:27.138: Se1/0 PPP: No remote authentication for call-in

*Sep 17 16:24:27.138: Se1/0 LCP: O CONFREQ [Listen] id 126 len 20

*Sep 17 16:24:27.138: Se1/0 LCP: ACCM 0x000A0000 (0x0206000A0000)

*Sep 17 16:24:27.138: Se1/0 LCP: MagicNumber 0x18DA576A (0x050618DA576A)

*Sep 17 16:24:27.138: Se1/0 LCP: PFC (0x0702)

*Sep 17 16:24:27.138: Se1/0 LCP: ACFC (0x0802)

*Sep 17 16:24:27.138: Se1/0 LCP: O CONFACK [Listen] id 81 len 20

*Sep 17 16:24:27.138: Se1/0 LCP: ACCM 0x000A0000 (0x0206000A0000)

*Sep 17 16:24:27.138: Se1/0 LCP: MagicNumber 0x01C6CCA9 (0x050601C6CCA9)

*Sep 17 16:24:27.138: Se1/0 LCP: PFC (0x0702)

*Sep 17 16:24:27.138: Se1/0 LCP: ACFC (0x0802)

*Sep 17 16:24:27.322: Se1/0 LCP: I CONFACK [ACKsent] id 126 len 20

*Sep 17 16:24:27.322: Se1/0 LCP: ACCM 0x000A0000 (0x0206000A0000)

*Sep 17 16:24:27.322: Se1/0 LCP: MagicNumber 0x18DA576A (0x050618DA576A)

*Sep 17 16:24:27.322: Se1/0 LCP: PFC (0x0702)

*Sep 17 16:24:27.322: Se1/0 LCP: ACFC (0x0802)

*Sep 17 16:24:27.322: Se1/0 LCP: State is Open

*Sep 17 16:24:27.322: Se1/0 PPP: No authorization without authentication

*Sep 17 16:24:27.322: Se1/0 PPP: Phase is FORWARDING, Attempting Forward

*Sep 17 16:24:27.322: Se1/0 PPP: Phase is ESTABLISHING, Finish LCP

*Sep 17 16:24:27.322: Se1/0 PPP: Phase is UP

*Sep 17 16:24:27.322: Se1/0 IPCP: O CONFREQ [Closed] id 1 len 10

*Sep 17 16:24:27.322: Se1/0 IPCP: Address 1.1.1.1 (0x030601010101)

*Sep 17 16:24:27.322: Se1/0 PPP: Process pending ncp packets

*Sep 17 16:24:27.326: Se1/0 IPCP: I CONFREQ [REQsent] id 1 len 10

*Sep 17 16:24:27.326: Se1/0 IPCP: Address 2.2.2.2 (0x030602020202)

*Sep 17 16:24:27.326: Se1/0 IPCP: O CONFACK [REQsent] id 1 len 10

*Sep 17 16:24:27.326: Se1/0 IPCP: Address 2.2.2.2 (0x030602020202)

*Sep 17 16:24:27.450: Se1/0 IPCP: I CONFACK [ACKsent] id 1 len 10

*Sep 17 16:24:27.450: Se1/0 IPCP: Address 1.1.1.1 (0x030601010101)

*Sep 17 16:24:27.450: Se1/0 IPCP: State is Open

*Sep 17 16:24:27.454: Se1/0 IPCP: Install route to 2.2.2.2

*Sep 17 16:24:27.454: Se1/0 DDR: dialer protocol up

*Sep 17 16:24:27.454: Se1/0 IPCP: Add link info for cef entry 2.2.2.2

*Sep 17 16:24:28.022: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1/0, changed state to up
   

Gibi çıktılar alıyorum.                        

  <http://www.sehenet.com/>              

Askin OZPOLAT

IT Manager/Consultant

askin_at_shyazilim.com <mailto:askin_at_shyazilim.com>

askin.ozpolat_at_sehenet.com <mailto:askin.ozpolat_at_sehenet.com>    

Yenibosna Datacenter <http://www.sehenet.com/>

Tel :212 552 6464

Faks:212 552 8899      

[Non-text portions of this message have been removed]

--
Cisco Teknik Tartisma Listesi (Cisco-ttl)

Bu listede onerilen degisikliklerin uygulanmasindaki tum sorumluluk 
kullaniciya aittir. Liste yoneticileri, oneride bulunan liste uyeleri ya da 
bu uyelerin calistigi kuruluslar herhangi bir sekilde sorumlu tutulamazlar. 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/cisco-ttl/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/cisco-ttl/join
    (Yahoo! ID required)

<*> To change settings via email:
    mailto:cisco-ttl-digest_at_yahoogroups.com 
    mailto:cisco-ttl-fullfeatured_at_yahoogroups.com

<*> To unsubscribe from this group, send an email to:
    cisco-ttl-unsubscribe_at_yahoogroups.com

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/