İLT: [cisco-ttl] ISND BRI Ses Tasima
From: Tonyukuk Özden (tozden_at_nettek.com.tr)
Date: Thu Mar 03 2005 - 15:45:51 EET
Tamer bey,
Ilginiz için teşekkür ederim. Tavsiye ettiğiniz şekilde yazdım. Lokasyonlar
birbirlerine ulaşabiliyorlar. Fakat arada yüksek oranda gürültü var.
Bir codec tanımlamak gerekir mi? Bu sorunu nasıl giderebiliriz.
Konu ile ilgili bir config guide var mı?
Iyi çalışmalar.
interface Ethernet0/0
ip address 192.168.0.1 255.255.255.0
full-duplex
!
interface Serial0/0
no ip address
encapsulation frame-relay IETF
no fair-queue
frame-relay lmi-type ansi
!
interface Serial0/0.1 point-to-point
ip address 192.168.155.2 255.255.255.252
frame-relay interface-dlci 16
!
interface TokenRing0/0
no ip address
shutdown
ring-speed 16
!
interface BRI1/0
no ip address
isdn switch-type basic-qsig
isdn overlap-receiving
isdn incoming-voice voice
isdn sending-complete
isdn skipsend-idverify
!
ip http server
ip classless
ip route 0.0.0.0 0.0.0.0 192.168.0.254
ip route 192.168.1.0 255.255.255.0 Serial0/0.1
!
!
!
!
voice-port 1/0/0
!
!
!
dial-peer voice 1 pots
destination-pattern 3..
direct-inward-dial
port 1/0/0
!
dial-peer voice 2 voip
destination-pattern 1..
session target ipv4:192.168.155.1
-----Özgün İleti-----
Kimden: Tamer AYDIN [mailto:tamer.aydin_at_nextiraone.com.tr]
Tarih: 03 Mart 2005 Perşembe 10:14
Kime: cisco-ttl_at_yahoogroups.com
Konu: RE: [cisco-ttl] ISND BRI Ses Tasima
Selam
Aşağıdaki gibi bir config yapmalısın..
Site-1
dial-peer voice 1 pots
destination-pattern 2..
direct-inward-dial
port 1/0/0
dial-peer voice 2 voip
destination-pattern 1..
session target ipv4:x.x.x.x(karşı taraf)
Site-2
dial-peer voice 1 pots
destination-pattern 1..
direct-inward-dial
port 1/0/0
dial-peer voice 2 voip
destination-pattern 2..
session target ipv4:y.y.y.y(karşı taraf)
-----Original Message-----
From: Tonyukuk Özden [mailto:tozden_at_nettek.com.tr]
Sent: Thursday, March 03, 2005 9:51 AM
To: cisco-ttl_at_yahoogroups.com
Subject: [cisco-ttl] ISND BRI Ses Tasima
Selamlar,
Topoloji şu şekilde ; her iki noktada santraller bri çıkışları router ın
vic bri s/t kartında sonlanıyor.
Santral - router arası qsig protokolu tanımlı. Bölgeler Frame relay devre
ile birbirine bağlı.
Santraller ile router konuşabiliyor.
interface BRI1/0
no ip address
isdn switch-type basic-qsig
isdn overlap-receiving
isdn incoming-voice voice
isdn sending-complete
isdn skipsend-idverify
Bir bölgeden diğerini arar iken numaralara nasıl route yazacağız. Santralden
örneğin 1** ile başlayan
Bir numara geldiğinde karşı tarafın bri portuna gitmesini nasıl sağlarız.
Teşekkür ederim
Tonyukuk Özden
[Non-text portions of this message have been removed]
--
Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.
Listede onerilen cozumlerin uygulanmasindaki tum sorumluluk kullaniciya
aittir. Liste yoneticileri, liste uyeleri ya da bu uyelerin calistigi
kuruluslar herhangi bir sekilde sorumlu tutulamazlar.
Listeden cikmak için cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir
e-posta gönderebilirsiniz.
Yahoo! Groups Links
--
Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.
Listede onerilen cozumlerin uygulanmasindaki tum sorumluluk kullaniciya
aittir. Liste yoneticileri, liste uyeleri ya da bu uyelerin calistigi
kuruluslar herhangi bir sekilde sorumlu tutulamazlar.
Listeden cikmak için cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir
e-posta gönderebilirsiniz.
Yahoo! Groups Links
--
Bu listenin Cisco Systems ile herhangi bir baglantisi bulunmamaktadir.
Listede onerilen cozumlerin uygulanmasindaki tum sorumluluk kullaniciya aittir. Liste yoneticileri, liste uyeleri ya da bu uyelerin calistigi kuruluslar herhangi bir sekilde sorumlu tutulamazlar.
Listeden cikmak için cisco-ttl-unsubscribe_at_yahoogroups.com adresine bir e-posta gönderebilirsiniz.
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/cisco-ttl/
<*> To unsubscribe from this group, send an email to:
cisco-ttl-unsubscribe_at_yahoogroups.com
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
This archive was generated by hypermail 2.1.3
: Thu Mar 03 2005 - 15:46:17 EET
|